| dbo:abstract
|
- Robik (rusky Робик) je ukrajinským počítačem kompatibilních s počítačem Sinclair ZX Spectrum. Jedná se o variantu počítače se 48 KiB paměti. Počítač byl vyráběn koncem 80. let a začátkem 90. let společností (rusky Ротор) v ukrajinském městě Čerkasy. Počítač podporuje i znaky cyrilice, kromě režimů klávesnice K, C, L, E a G ZX Spectra je přidán režim psaní ruských písmen Л. Díky přítomnosti ruské znakové sady v paměti ROM nefungují na tomto počítači některé programy, které nastavují registr I procesoru na hodnotu v rozsahu 38 až 3B šestnáctkově. Počítač byl vyráběn ve čtyřech variantách, ve třetí verzi byla přepsána obsluha klávesnice. Počítač umožňuje připojování rozšiřovacích modulů, ovšem ve většině případů je nutné upravit pravou stranu klávesnice. (cs)
- Robik was a ZX Spectrum clone produced between 1989 and 1994 by Selto-Rotor (scientifically technical industrial creative association), a former military factory. The computer came with a full QWERTY keyboard with 55 keys, separate EDIT, three SHIFTS, double RESET, DEL, separate comma and full stop keys. It had the possibility to switch between Latin and Russian fonts. It had built-in Kempston interface and cursor keys that also worked as a joystick. It had no edge connector and video output was RGB on a 5-pin DIN or on an 8-pin DIN (for connecting to HERCULES or EGA monitor). There was no composite video and all I/O ports were 5- and 7-pin DINs. Inside the case there was a male 64-pin connector that could be mapped to the standard edge connector. The hardware contained about three to four grams of gold and almost eighteen grams of silver. The letters on the keyboard were written using laser beam technology. The buttons used reed switches instead of copper or iron contact plates. When writing, the screen memory to the TV/monitor screen did not begin from the top left of the border, but instead began from border right under paper. This meant that most multicolor effects and some games did not work correctly. Errors in the ROM have been fixed and Cyrillic letters were also inserted. The keyboard matrix was extended from five keys in eight rows to five keys in nine rows to allow for more buttons. A reset could be performed by pressing two reset buttons. The Robik came in four versions with only minor changes made for Russian internationalization and localization. The hardware remained largely unchanged, but cheaper parts were used for each version. The fourth version had the new addition of a single integrated circuit. This version did not sell well because by then the main market for the Robik was hardware enthusiasts and this design did not allow for modifications. Robik had two EPROM chips. There are two languages in the M2764AF-1 chip from ST, which can be switched by shortcut keys. (en)
|
| dbo:wikiPageID
| |
| dbo:wikiPageLength
|
- 3753 (xsd:nonNegativeInteger)
|
| dbo:wikiPageRevisionID
| |
| dbo:wikiPageWikiLink
| |
| dbp:wikiPageUsesTemplate
| |
| dcterms:subject
| |
| gold:hypernym
| |
| rdf:type
| |
| rdfs:comment
|
- Robik (rusky Робик) je ukrajinským počítačem kompatibilních s počítačem Sinclair ZX Spectrum. Jedná se o variantu počítače se 48 KiB paměti. Počítač byl vyráběn koncem 80. let a začátkem 90. let společností (rusky Ротор) v ukrajinském městě Čerkasy. Počítač podporuje i znaky cyrilice, kromě režimů klávesnice K, C, L, E a G ZX Spectra je přidán režim psaní ruských písmen Л. Díky přítomnosti ruské znakové sady v paměti ROM nefungují na tomto počítači některé programy, které nastavují registr I procesoru na hodnotu v rozsahu 38 až 3B šestnáctkově. (cs)
- Robik was a ZX Spectrum clone produced between 1989 and 1994 by Selto-Rotor (scientifically technical industrial creative association), a former military factory. The computer came with a full QWERTY keyboard with 55 keys, separate EDIT, three SHIFTS, double RESET, DEL, separate comma and full stop keys. It had the possibility to switch between Latin and Russian fonts. It had built-in Kempston interface and cursor keys that also worked as a joystick. It had no edge connector and video output was RGB on a 5-pin DIN or on an 8-pin DIN (for connecting to HERCULES or EGA monitor). There was no composite video and all I/O ports were 5- and 7-pin DINs. Inside the case there was a male 64-pin connector that could be mapped to the standard edge connector. (en)
|
| rdfs:label
| |
| owl:sameAs
| |
| prov:wasDerivedFrom
| |
| foaf:isPrimaryTopicOf
| |
| is dbo:wikiPageWikiLink
of | |
| is foaf:primaryTopic
of | |
