| dbo:abstract
|
- In telecommunications, signal reflection occurs when a signal is transmitted along a transmission medium, such as a copper cable or an optical fiber. Some of the signal power may be reflected back to its origin rather than being carried all the way along the cable to the far end. This happens because imperfections in the cable cause impedance mismatches and non-linear changes in the cable characteristics. These abrupt changes in characteristics cause some of the transmitted signal to be reflected. In radio frequency (RF) practice this is often measured in a dimensionless ratio known as voltage standing wave ratio (VSWR) with a VSWR bridge. The ratio of energy bounced back depends on the impedance mismatch. Mathematically, it is defined using the reflection coefficient. Because the principles are the same, this concept is perhaps easiest to understand when considering an optical fiber. Imperfections in the glass create mirrors that reflect the light back along the fiber. Impedance discontinuities cause attenuation, attenuation distortion, standing waves, ringing and other effects because a portion of a transmitted signal will be reflected back to the transmitting device rather than continuing to the receiver, much like an echo. This effect is compounded if multiple discontinuities cause additional portions of the remaining signal to be reflected back to the transmitter. This is a fundamental problem with the daisy chain method of connecting electronic components. When a returning reflection strikes another discontinuity, some of the signal rebounds in the original signal direction, creating multiple echo effects. These forward echoes strike the receiver at different intervals making it difficult for the receiver to accurately detect data values on the signal. The effects can resemble those of jitter. Because damage to the cable can cause reflections, an instrument called an electrical time-domain reflectometer (ETDR; for electrical cables) or an optical time-domain reflectometer (OTDR; for optical cables) can be used to locate the damaged part of a cable. These instruments work by sending a short pulsed signal into the cable and measuring how long the reflection takes to return. If only reflection magnitudes are desired, however, and exact fault locations are not required, VSWR bridges perform a similar but lesser function for RF cables. The combination of the effects of signal attenuation and impedance discontinuities on a communications link is called insertion loss. Proper network operation depends on constant characteristic impedance in all cables and connectors, with no impedance discontinuities in the entire cable system. When a sufficient degree of impedance matching is not practical, echo suppressors or echo cancellers, or both, can sometimes reduce the problems. The Bergeron diagram method, valid for both linear and non-linear models, evaluates the reflection's effects in an electric line. (en)
- Эхо — метод контроля передаваемой информации посредством возврата информации отправителю от получателя или от одного из узлов в цепи передачи. Метод широко используется в модемах, где на аппаратном уровне существует возможность управления эхом при помощи команд «echo on» или «echo off». Эхо используется для проверки коммуникационного оборудования на стороне отправителя, для проверки линии связи, для проверки коммуникационного оборудования со стороны получателя. При использовании эха отправитель обладает не только отправленной информацией, но и информацией прошедшей путь до получателя. При логировании эхо позволяет точно определить моменты задержек и получить полную картину процесса передачи данных. (ru)
|
| dbo:thumbnail
| |
| dbo:wikiPageID
| |
| dbo:wikiPageLength
|
- 4066 (xsd:nonNegativeInteger)
|
| dbo:wikiPageRevisionID
| |
| dbo:wikiPageWikiLink
| |
| dbp:wikiPageUsesTemplate
| |
| dcterms:subject
| |
| rdf:type
| |
| rdfs:comment
|
- Эхо — метод контроля передаваемой информации посредством возврата информации отправителю от получателя или от одного из узлов в цепи передачи. Метод широко используется в модемах, где на аппаратном уровне существует возможность управления эхом при помощи команд «echo on» или «echo off». Эхо используется для проверки коммуникационного оборудования на стороне отправителя, для проверки линии связи, для проверки коммуникационного оборудования со стороны получателя. При использовании эха отправитель обладает не только отправленной информацией, но и информацией прошедшей путь до получателя. При логировании эхо позволяет точно определить моменты задержек и получить полную картину процесса передачи данных. (ru)
- In telecommunications, signal reflection occurs when a signal is transmitted along a transmission medium, such as a copper cable or an optical fiber. Some of the signal power may be reflected back to its origin rather than being carried all the way along the cable to the far end. This happens because imperfections in the cable cause impedance mismatches and non-linear changes in the cable characteristics. These abrupt changes in characteristics cause some of the transmitted signal to be reflected. In radio frequency (RF) practice this is often measured in a dimensionless ratio known as voltage standing wave ratio (VSWR) with a VSWR bridge. The ratio of energy bounced back depends on the impedance mismatch. Mathematically, it is defined using the reflection coefficient. (en)
|
| rdfs:label
|
- Signal reflection (en)
- Эхо (коммуникации) (ru)
|
| owl:sameAs
| |
| prov:wasDerivedFrom
| |
| foaf:depiction
| |
| foaf:isPrimaryTopicOf
| |
| is dbo:wikiPageDisambiguates
of | |
| is dbo:wikiPageRedirects
of | |
| is dbo:wikiPageWikiLink
of | |
| is rdfs:seeAlso
of | |
| is foaf:primaryTopic
of | |
