Due to the plastic-elastic characteristic of a metal, it is typical that any deformation of sheet metal at room temperature will have both elastic and plastic deformation. After the metal workpiece is removed from the tool or deformation implement, the elastic deformation will be released and only the plastic deformation will remain. When a metal forming tool is planned and designed to deform a workpiece, the shape imparted by the tool will be a combination of elastic and plastic deformation. The release of the elastic deformation is the spring back often observed at the end of a metal forming process. The spring back has to be compensated to achieve an accurate result.
| Attributes | Values |
|---|
| rdf:type
| |
| rdfs:label
| - Rückfederungskompensation (de)
- Spring Back Compensation (en)
|
| rdfs:comment
| - Die Rückfederungskompensation ist der Ausgleich der Rückfederung, die beim maßgenauen Biegen eines Werkstücks mitberücksichtigt werden muss. (de)
- Due to the plastic-elastic characteristic of a metal, it is typical that any deformation of sheet metal at room temperature will have both elastic and plastic deformation. After the metal workpiece is removed from the tool or deformation implement, the elastic deformation will be released and only the plastic deformation will remain. When a metal forming tool is planned and designed to deform a workpiece, the shape imparted by the tool will be a combination of elastic and plastic deformation. The release of the elastic deformation is the spring back often observed at the end of a metal forming process. The spring back has to be compensated to achieve an accurate result. (en)
|
| foaf:depiction
| |
| dct:subject
| |
| Wikipage page ID
| |
| Wikipage revision ID
| |
| Link from a Wikipage to another Wikipage
| |
| sameAs
| |
| dbp:wikiPageUsesTemplate
| |
| thumbnail
| |
| has abstract
| - Die Rückfederungskompensation ist der Ausgleich der Rückfederung, die beim maßgenauen Biegen eines Werkstücks mitberücksichtigt werden muss. (de)
- Due to the plastic-elastic characteristic of a metal, it is typical that any deformation of sheet metal at room temperature will have both elastic and plastic deformation. After the metal workpiece is removed from the tool or deformation implement, the elastic deformation will be released and only the plastic deformation will remain. When a metal forming tool is planned and designed to deform a workpiece, the shape imparted by the tool will be a combination of elastic and plastic deformation. The release of the elastic deformation is the spring back often observed at the end of a metal forming process. The spring back has to be compensated to achieve an accurate result. Usually, that is realized by overbending the material corresponding to the magnitude of the spring back. That means for the practical side of the bending process; the bending former, enters deeper into the bending prism. For other sheet metal forming operations like drawing, it entails deforming the sheet metal past the planned net shape of the part, so that when the spring back is released from the part, the plastic deformation in that part delivers the desired shape of the part. In the case of complex tools, the spring back has to be already considered in the engineering and construction phases. Therefore, complex software simulations are used. Frequently this is not enough to deliver the desired results. In such cases practical experiments are done, using the trial-and-error plus experience method to correct the tool. However, the results (work pieces) are only stable, if all influencing factors are the same. This mainly includes:
* Yield strength of the sheet
* Chemical composition of the sheet
* Structure of the material (e.g., direction of grain during production process)
* Wear of tools
* Material temperature
* Aging processes of the raw material (significant for aluminum and copper)
* Deformation rate The list of factors may be continued. Spring back assessment of final formed products is a difficult problem and is affected by the complexity of the formed shape. The NUMISHEET 93 conference benchmark problem involves the draw bending of a U-channel using three measured parameters. Parameter less approaches have been proposed for more complex geometries but need validation. (en)
|
| prov:wasDerivedFrom
| |
| page length (characters) of wiki page
| |
| foaf:isPrimaryTopicOf
| |
| is Link from a Wikipage to another Wikipage
of | |
| is Wikipage disambiguates
of | |
| is foaf:primaryTopic
of | |
![[RDF Data]](/fct/images/sw-rdf-blue.png)
![[cxml]](/fct/images/cxml_doc.png)
![[csv]](/fct/images/csv_doc.png)
![[text]](/fct/images/ntriples_doc.png)
![[turtle]](/fct/images/n3turtle_doc.png)
![[ld+json]](/fct/images/jsonld_doc.png)
![[rdf+json]](/fct/images/json_doc.png)
![[rdf+xml]](/fct/images/xml_doc.png)
![[atom+xml]](/fct/images/atom_doc.png)
![[html]](/fct/images/html_doc.png)
