A quarter panel (British English: rear wing) is the body panel (exterior surface) of an automobile between a rear door (or only door on each side for two-door models) and the trunk (boot) and typically wraps around the wheel well. The similar front section between the door and the hood (bonnet) is called a fender (front wing), and may sometimes also be referred to as a quarter panel. Quarter panels are typically made of sheet metal, but are sometimes made of fiberglass, carbon fiber, or fiber-reinforced plastic.
Attributes | Values |
---|
rdf:type
| |
rdfs:label
| - クォーター・パネル (ja)
- Quarter panel (en)
|
rdfs:comment
| - クォーター・パネルまたはコーター・パネル (Quarter panel) とは、自動車の外装の一部を指す言葉であり、ドアとボンネット(イギリス英語であり、アメリカ英語ではフードと言う)には挟まれた箇所、および、ドアとトランクリッドにはさまれた箇所、いずれかまたは両方を指す用語。通常、フロントおよびリアのを取り囲んでいるパネルである。フロント・クォーター・パネルはAピラーまで、リア・クォーター・パネルはCピラーまで含んでプレス成形されている場合もある。現代では、フロントのクォーター・パネルはフェンダーと一体になっていることが多い。 クォーター・パネルの素材は鋼板が一般的であるが、FRPや熱可塑性樹脂が用いられることもある。 (ja)
- A quarter panel (British English: rear wing) is the body panel (exterior surface) of an automobile between a rear door (or only door on each side for two-door models) and the trunk (boot) and typically wraps around the wheel well. The similar front section between the door and the hood (bonnet) is called a fender (front wing), and may sometimes also be referred to as a quarter panel. Quarter panels are typically made of sheet metal, but are sometimes made of fiberglass, carbon fiber, or fiber-reinforced plastic. (en)
|
foaf:depiction
| |
dcterms:subject
| |
Wikipage page ID
| |
Wikipage revision ID
| |
Link from a Wikipage to another Wikipage
| |
sameAs
| |
dbp:wikiPageUsesTemplate
| |
thumbnail
| |
has abstract
| - A quarter panel (British English: rear wing) is the body panel (exterior surface) of an automobile between a rear door (or only door on each side for two-door models) and the trunk (boot) and typically wraps around the wheel well. The similar front section between the door and the hood (bonnet) is called a fender (front wing), and may sometimes also be referred to as a quarter panel. Quarter panels are typically made of sheet metal, but are sometimes made of fiberglass, carbon fiber, or fiber-reinforced plastic. A quarter panel is typically a welded-on component of the unibody structure. Replacement of a sheet metal quarter panel typically requires it to be cut off the vehicle and a replacement part to be welded (or sometimes bonded) to the vehicle. Due to the high amount of specialized labor, a quarter panel may often be repaired rather than replaced by hammering the damaged area to a relatively flat surface and then applying a body filler to smooth out the damaged area to match the original surface. The panel is then usually painted and often clear coated. (en)
- クォーター・パネルまたはコーター・パネル (Quarter panel) とは、自動車の外装の一部を指す言葉であり、ドアとボンネット(イギリス英語であり、アメリカ英語ではフードと言う)には挟まれた箇所、および、ドアとトランクリッドにはさまれた箇所、いずれかまたは両方を指す用語。通常、フロントおよびリアのを取り囲んでいるパネルである。フロント・クォーター・パネルはAピラーまで、リア・クォーター・パネルはCピラーまで含んでプレス成形されている場合もある。現代では、フロントのクォーター・パネルはフェンダーと一体になっていることが多い。 クォーター・パネルの素材は鋼板が一般的であるが、FRPや熱可塑性樹脂が用いられることもある。 (ja)
|
prov:wasDerivedFrom
| |
page length (characters) of wiki page
| |
foaf:isPrimaryTopicOf
| |
is Link from a Wikipage to another Wikipage
of | |
is Wikipage redirect
of | |
is foaf:primaryTopic
of | |